Tag/tag.png

Unsupported Version
This article applies to an unsupported version of Ubuntu. More info...

IMPORTANT NOTE

This information is outdated. Please visit the Ubuntu LTSP community wiki at https://help.ubuntu.com/community/UbuntuLTSP for current information regarding Ubuntu and LTSP. Thanks!!


NOTE

While this howto explains thin client functionality very well, the setup procedure refers to a (very) old version - Ubuntu breezy (5.10). For current installation instructions for the latest version of Ubuntu, please see https://help.ubuntu.com/community/UbuntuLTSP/LTSPQuickInstall - or for the Ubuntu LTSP community wiki home, see https://help.ubuntu.com/community/UbuntuLTSP

How do thin clients work?

Thin clients are computers that load and run most of their programs from a central server, but are displayed on the thin client's screen. In more technical terms, the thin client can either obtain a kernel from local storage, or load the kernel across the network. (Using these instructions, you will collect the linux kernel from the server using a bootable network card. This way, the thin client needs no more storage than the boot rom built into a bootable network card.)

Boot sequence

The PXE network card makes a DHCP request on the local network. The DHCP reply gives information to the card where to collect the linux kernel from. The kernel is collected over the network through the TFTP protocol.

Once the kernel has been collected via TFTP, the kernel is executed; the machine boots linux. A initramfs collected with the linux kernel is mounted as a root file system. This carries and autodetect the necessary drivers for the network card, mouse, keyboard sound etc. Once the network card driver is loaded, a second DHCP request tells the client its ip address, netmask, gateway, DNS server, and root NFS (Network File System) mount point.

The linux kernel runs the ubuntu initramfs, which mounts the root NFS share from the server onto the thin client read-only. The thin client now has a booted linux kernel and a root file system, much like any Linux system. From now on, when we talk of the root file system on the client, we are actually talking about a root file system mounted read-only from the server. The root file system mounted by the thin client is not the same root file system the server itself uses, but is specially prepared for thin clients, and is shared by all thin clients connected to the server (located in /opt/ltsp/<arch> on the server) . The initramfs calls the init program, the Xserver settings are autodetected and the ubuntu breezy ltsp login manager, ldm, is started.

X nuts and bolts

After logging in, ldm starts a ssh tunnel and executes a X session on the server which is displayed through the tunnel on the thin client's X server. Using ssh here has the big advantage that you don't need to have a Xserver configured on the client and no unsafe TCP X transport is used as was done in older days of ltsp.

Requirements

You will need:

  • An Ubuntu 5.10 system to be the server
  • At least one PXE-bootable system to be a client
  • Plenty of disk space
  • A fast network connection, or a local Breezy mirror, or some patience
  • A DHCP server which is capable of supporting PXE clients, or a separate network segment where you can run a dedicated DHCP server
  • Command-line familiarity
  • A sense of adventure
  • A burning desire to send feedback to ubuntu-devel

Warnings

Getting Started

NOTE: If you plan to use the server as gateway/nat/firewall machine, it is strongly suggested to configure all the network interfaces before proceeding with the following steps.

  1. Set up the DHCP server
    • If you have an existing DHCP server which can support PXE clients:
      • Configure it to pass a boot filename of /ltsp/pxelinux.0 and a root path of /opt/ltsp/i386

      • If you are using Edgy Eft, so a boot filename is /ltsp/i386/pxelinux.0. The root path is the same as above.

      • For ISC DHCPD, use the following options:

        filename "/ltsp/pxelinux.0";
        option root-path "/opt/ltsp/i386";
      • Install ltsp-server on the server:

        sudo apt-get install ltsp-server
    • If you want to run a dedicated DHCP server on the thin client server:
      1. Install ltsp-server-standalone on the server:

        sudo apt-get install ltsp-server-standalone
      2. If necessary, customize /etc/ltsp/dhcpd.conf (by default it's configured for a server at 192.168.0.1 serving PXE clients)

      3. If you are running a firewall on the server, you'll need to open TFTP and NFS (and DHCP if you're running the standalone server). Also, make sure portmap isn't limited to the loopback interface in /etc/default/portmap (comment out the line with "-i 127.0.0.1") if it exists, could be a leftover from Hoary. You also may want to edit `/etc/hosts.allow' and limit access for portmap, rpc.mountd, rpc.statd, and in.tftpd to the local network:

        portmap:    192.168.0.0/24
        rpc.mountd: 192.168.0.0/24
        rpc.statd:  192.168.0.0/24
        in.tftpd:   192.168.0.0/24
      4. Restart the nfs subsystem:

        sudo invoke-rc.d nfs-kernel-server restart
        sudo invoke-rc.d nfs-common restart
        sudo invoke-rc.d portmap restart 
  2. Build the thin client runtime environment:

    sudo ltsp-build-client
    • This script is hardcoded to use a particular Ubuntu mirror, so you may wish to edit it if you have a nearby mirror or CD (sudo ltsp-build-client --mirror file:///cdrom), remember to copy sources.list from the server into the chroot)

    • If you changed your aptitude dependency-settings not to select recommended packages automatically, not all required packages will be downloaded and installed by this script. Then no login with sdm is possible for example because some parts of the x-server are missing
  3. sudo apt-get install openssh-server
    sudo ltsp-update-sshkeys

    Check /opt/ltsp/i386/etc/ssh/ssh_known_hosts and ensure that your host key is associated with your host's IP address. Depending on your /etc/hosts configuration, this may not always be correct automatically (yet). If it looks like this:

    servername ssh-rsa AAAAB3NzaC1yc2EAAAABI...

    then add the IP address like this:

    servername,192.168.0.1 ssh-rsa AAAAB3NzaC1yc2EAAAABI...

    AND file a bug in [https://launchpad.net/malone Malone]. THIS SHOULD NOT HAPPEN.

  4. sudo invoke-rc.d dhcp3-server start
  5. Optionally, create /opt/ltsp/i386/etc/lts.conf. If you don't create one, reasonable defaults and auto-detected values will be used. Note: Not all options are supported (see EdubuntuLtsConfParams).

  6. PXE boot the client and see what happens. If all goes well, you should see a graphical login dialog.
  7. If your client doesn't have PXE on the network card, you can generate a custom boot CD or floppy at ROM-o-matic.net. Burn the ISO or floppy image and boot from that.

  8. Log in, with any user authorized to login remotely via ssh, and see what happens. If all goes well, you should get a working desktop session on the server.
  9. Send mail to ubuntu-devel with your findings

Tips

If you have a separate DHCP that you do not want to install LTSP on you can just redirect the thin-client to boot off a different server.

In your DHCP server's dhcpd.conf:

next-server 192.168.0.3;

where 192.168.0.3 is the address of your LTSP server

If your thin client does not start to the X and you will see the message NFS Server not responding still trying, so please add text

NFSOPTS="-o nolock,ro,wsize=2048,rsize=2048"

to the default tftp config in /var/lib/tftpboot/ltsp/i386/pxelinux.cfg/default.

Bugs

  • Bug 25528: [FIX RELEASED] OpenSSH doesn't appear to release ports used for X forwarding in a timely manner, preventing you from logging out and logging back in immediately when IPv6 support is enabled. Disable it by adding "AddressFamily inet" to /etc/ssh/sshd_config, and restarting the openssh daemon.

Extras

  1. ThinClientHowtoNAT


ThinClientHowto (last edited 2010-06-08 12:17:37 by arauzo)